I’ve been doing an increasing number of DCC decoder installations and model locomotive repair jobs – both for myself and others – and setting up my tester and rolling road each and every time I needed them was becoming a bit tiresome (not to mention the rat’s nest of cables).
After pulling what’s left of my hair out for the final time, I decided to put together a small loco and decoder test board, incorporating my LokProgrammer and SPROG, as well as accommodating off-board control integration (DCC and DC/Analogue).
The board also features a rolling road, using DCC Concepts rolling road modules, and my own take on a means to permanently integrate them into a test set up and improve usability, using acrylic sheet, spacers and screws.
You can download a PDF version of the wiring diagram for the test board featured in the video via the link below:
Wiring Diagram for DCC Decoder Test Board & Rolling Road 5.98 MB 490 downloadsThis is a wiring diagram for the decoder/loco test boar and rolling road featured...
This is only one way of approaching a decoder test board setup and there other examples out there. I do recommend that you consider something like this if you’re intending to do a lot of decoder installation and maintenance – it saves a lot of time and hassle!
CORRECTION: in the video, I mention the acrylic/perspex sheet as being 6mm when it is actually 4mm. A thickness of 6mm is likely to be too thick and may interfere with the wheel flanges.
You can buy some components for this how-to project via the links below. Buying via Amazon affiliate links means I get a (very) small donation and helps to support the website and channel:
– DCC Concepts rolling road: https://amzn.to/2C1IB6t
– Red and black wire pack: https://amzn.to/2C1Infx
– Green 2-pin terminal plugs/sockets: https://amzn.to/2PiVfiW
– Peco straight track: https://amzn.to/2LGgPM7
– A4 clear acrylic sheet (4mm thick): https://amzn.to/2Cae1Yk
– M5x8mm black nylon spacer: https://amzn.to/2Pq7tX4
– A4 plywood 12mm: https://ebay.us/LGRLYW
– A4 plywood 3mm: https://amzn.to/2C03bE2
– ESU decoder tester: https://ebay.us/aBLzSi
– SPROG dcc module: http://www.sprog-dcc.co.uk
– Green power panel-mount socket/plug: https://ebay.us/nBLfXz
– DC power-style socket: https://ebay.us/nBLfXz
– 3 position, 2-pole switch: https://ebay.us/WyKD3b
3D Printer STL Files
If you’ve got a 3D printer, you can download STL file for the 3D-designed parts for free and print yourself a copy:
Please note: If you choose to follow any of the steps or suggestions outlined in the video, you do so at your own risk and any damage or injury to yourself, your models, your equipment or others is your own responsibility. Your own test board wiring requirements will vary depending on the components that you use and also the specifics of your design. The diagram provided above is only a guide and you must work out your own wiring needs yourself to avoid costly damage to programmers, testers and decoders.
We’re working on a short tutorial looking at DCC decoder installation in older locomotives, such as Lima and Hornby, that are powered by ringfield/pancake-style motors.
To accompany the tutorial, we’ve produced a PDF containing a series of basic wiring diagrams to help with the installation process. They cover the more modern can-style motors (as found in Bachmann, Heljan, Dapol etc.) as well as the older ringfield ones (similar to those found in many Hornby and Lima models).
There’s also a basic diagram for directional lighting and a single Aux channel, such as the Aux 1/green wire available on most low/mid-range decoders, such as Hornby’s entry level R8249 8-pin variety.
The wiring principles would be the same for older ‘grain of wheat’ bulbs, although the resistor value would need to be altered to suit the bulb and track voltage.
You can download the PDF by clicking here.